WEW-300B computer screen display hydraulic universal testing machine

1. Equipment parameters and configuration

Two. Main uses:

The WEW series microcomputer screen type hydraulic universal testing machine is mainly used for tensile tests, compression and bending tests of metallic materials. The concrete, brick, tile, rubber and their products can be tested after adding the corresponding accessories.

This machine is made up of a dual column, double screw cylinder, lower cylinder main engine and a piano type oil source control cabinet. The oil pump adopts the low noise and high performance gear pump imported from Italy Mazu. The drawing space is above the main engine, and the compression and bending test space is located between the main beam and the work table. The adjustment of the test space is realized through the movement of the middle beam, and the middle beam is lifted by chain drive.

The test process adopts hydraulic manual loading, sensor force measurement, computer screen real-time display, automatic storage and printing function, and hydraulic automatic clamping of sample. After the test, the maximum force, tensile strength, yield strength, modulus of elasticity, elongation after failure and shrinkage of the section were obtained automatically.

Three. Function and characteristics:

The special super thick pincer seat makes the jaw fully contained in the seat of the jaw when holding the sample with the jaw, so that the clamp is more reliable, and the possibility of the deformation and damage of the horn shape is eliminated, and the service life of the equipment is greatly improved.

The wear-resistant lining plate is added between the jaw seat and the clamp plate, and the phenomenon that the oxide skin falls into the scrap of the slant surface of the jaw seat is eliminated during the metal stretching process, making the clamping process more slippery and more firmly clamped.

The machine has stable balance, low noise, high efficiency and wide speed range.

Four. The introduction of software function

The advantages of the system:

(1) the whole system has no potentiometers and other adjustable devices.

(2) the system is all digital design with high accuracy, stability and safety.

(3) the system adopts digital zero adjustment and parameter calibration.

(4) the system control parameters can be automatically calibrated, and no system can be used after the technician has left.

(5) after the test, the system automatically analyzes the test data and curves, and can also be analyzed under manual intervention.

(6) special test reports can be customized according to customer requirements.

(7) system software integrates more than thirty national standards or test methods such as GB/T228-2002;

(8) the software is simple and easy to operate.

(9) the software can display the loading speed of the load;

(10) query, print and browse test data through the network.

Five. Brief introduction of measurement and control software:

(1) introduction of MaxTest software:

Based on the WINDOWS operation platform, the software is simple and powerful, and has a human-machine conversation structure.

Four digit digital display test force value, accuracy for each gear range 20% starts to show the value of + 1%;

In four files, the digital display is deformed, and the accuracy is 20% for each gear range 20%.

At the same time, recording force time, deformation time, force deformation test curve, can switch observation at any time, random zoom down, horizontal or vertical movement, real-time high-speed sampling;

On the basis of automatic analysis, the results of elastic modulus, yield strength, tensile strength and so on are automatically calculated at the end of the test, and the accuracy of the analysis can be improved by manual analysis.

Test data is managed by standard database, and all test data and curves are automatically saved.

During test, the test curve is displayed in real time. After testing, the test data, curves and information of the test piece will be displayed in this operation window.

This set of control software has now integrated more than 100 national standards or test methods, so many national standards can meet the needs of customers' multifaceted test. The test report method can be customized and updated at any time according to the needs of the customer, which can bring great convenience to the customers.

The database can be Querying Historical test data, and only need to input certain conditions to find the test data immediately.

The force and deformation can be automatically calibrated. After we have completed the debugging, if the user is not allowed to feel the indication or the measurement parameters are changed, only click the automatic correction button, and the system parameters will be restored to the state of the debug.

Only use the mouse to operate on the two acquisition channels can be zero, the system is usually only once zero zero, in normal use, the system will automatically return to the real zero point;

A group of similar samples can be aggregated and analyzed, and the measured data can be compared and the average value can be calculated, so that the samples can be aggregated and printed in batches.

To provide multiple forms of report printing, users can edit any format report as required.

Control programmer, MaxDoc report processor, MaxXls report processor, etc.

Six. Quality assurance

After the formal acceptance of the equipment, the equipment shall be regarded as a formal delivery. The three period of the equipment is one year from the date of formal delivery (except for the other delay stipulated by the supplier). In the three package period, the supplier will service and repair all kinds of malfunctions of the equipment in time. During the operation of the warranty, the supplier will be in trouble with the ordering party and assist the ordering party to complete the maintenance task.

Seven, after sale quality service

1. After the formal acceptance of the equipment, the equipment shall be regarded as a formal delivery. The three package period is one year from the date of formal delivery. The longest quality of individual parts is 3 years

2. Training

(1) our test crew arrives at the demand side, and our personnel arrive at the scene to debug. Free of charge for 1-2 operators of the demand side, the training place can be in the demand side company, or in our company.

(2) training must be carried out correctly using test machines, software operations and general maintenance and troubleshooting.

3. Maintenance service

(1) the consulting service provider will answer the questions on the phone or written in writing at any time.

(2) during the period of fault maintenance, the supplier will make a troubleshooting plan for the users within 24 hours and notify the users. If the supplier fails to solve the problem, the supplier will send someone to the service.

(3) only the maintenance cost is charged for the failure or damage caused by the natural person during the warranty period.

4. The following conditions are not in the scope of warranty

(1) failure or damage caused by abnormal operation and man-made or natural disasters.

(2) without our consent, we will demolished the damaged parts (such as microcomputer, mainframe, line, etc.).

(3) without our consent to install the virus software, arbitrary delete computer files or autolysis registration number can not work normally cause the test machine can not work.

5. Update service

(1) upgrade test software for users free of charge, and expand the experimental function for users.

(2) other accessories purchased by the user only charge materials and processing fees, and no management fees are charged.

Ji'nan Heng Xu Test Machine Technology Co., Ltd.

Contact phone: 0531-85860713 858607223

Contact: Tang Xueying 15508660930